Brother CS-6000 Sewing Machine Manual

The Brother CS-6000 is a versatile computerized sewing machine featuring 60 built-in stitches, automatic needle threading, a wide table, LCD display, adjustable sewing speed, automatic thread cutter, and one-step buttonhole. It includes accessories for quilting, sewing, and embroidery. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: LCD display, stitch selection dial, automatic needle threader, wide table, drop-in bobbin system, built-in LED light, foot pedal, accessory storage.

Installation & Setup

Unpack and inspect contents. Place on stable, flat surface.

1. Attach wide table: Slide onto free arm until it clicks into place.
2. Install foot pedal: Connect plug to machine port, place on floor.
3. Connect power: Plug power cord into machine and wall outlet.
4. Wind bobbin: Place thread on spool pin, follow path to bobbin winder.
5. Insert bobbin: Place bobbin in case with thread clockwise, pull thread through slot.
6. Thread upper thread: Follow numbered path, use automatic needle threader.

WARNING! Keep fingers away from needle area during setup. Ensure machine is unplugged when threading bobbin.

First-Time Operation

Plug in power, turn on machine, follow these steps.

1. Select stitch: Turn stitch selection dial to desired pattern (LCD shows number).
2. Attach presser foot: Raise presser foot lever, snap foot into place.
3. Adjust stitch settings: Use buttons to set length (0-5mm) and width (0-7mm).
4. Test sew: Place fabric under foot, lower presser foot, gently press foot pedal.
5. Use automatic thread cutter: Press thread cutter button after sewing.

CAUTION! Always lower presser foot before sewing. Do not pull fabric; let feed dogs move it.

Specifications

• Model: Brother CS-6000 Computerized Sewing Machine.
• Stitches: 60 built-in stitches (utility, decorative, quilting, heirloom).
• Buttonholes: 7 one-step automatic buttonhole styles.
• Speed: Up to 850 stitches per minute, adjustable.
• Needle Positions: Left, center, right adjustment.
• Presser Feet: Includes zigzag foot, buttonhole foot, zipper foot, walking foot, quilting foot, blind stitch foot, overcasting foot, monogramming foot, button sewing foot.
• Display: LCD screen with stitch number and settings.
• Power Supply: 120V AC, 60Hz.
• Dimensions: 16.3" x 7.2" x 12.2" (without wide table).
• Weight: 13.2 lbs.

Controls and Settings

Front Panel: Power switch, stitch selection dial, LCD, stitch length/width buttons, reverse stitch button, needle up/down button, automatic thread cutter button.

Stitch Settings: Length (0-5mm), Width (0-7mm), Mirror image, Twin needle mode. Utility Stitches: Straight, zigzag, stretch, blind hem, overcasting. Decorative Stitches: Scallop, honeycomb, smocking, cross stitch. Memory: Can store custom stitch settings.

Stitch Selection & Functions

Turn dial to select stitch; LCD shows number and recommended foot.

1. Straight stitch: For seams, topstitching (adjust length for fabric).
2. Zigzag stitch: For finishing edges, appliqué (adjust width).
3. Buttonhole: Select buttonhole stitch, use foot to measure button.
4. Decorative stitches: Use stabilizer for best results on lightweight fabrics.
5. Quilting stitches: Use walking foot for even fabric feeding.
6. Blind hem: Fold fabric as instructed, use blind hem foot.

Tip: Always test stitch on scrap fabric first. Use appropriate needle for fabric type.

Using Accessories

Included accessories: Wide table, assorted presser feet, bobbins, needles, screwdriver, brush, seam ripper, spool caps.

1. Change presser foot: Raise lever, press button on back of foot to release.
2. Install zipper foot: Attach to right or left side for zipper insertion.
3. Use walking foot: For quilting or layered fabrics to prevent shifting.
4. Attach darning foot: For free-motion sewing or embroidery.
5. Use spool caps: For cross-wound threads to prevent tangling.

WARNING! Ensure needle is up and machine is off when changing feet. Use correct foot for selected stitch.

Maintenance & Cleaning

Unplug machine before maintenance. Clean lint and dust regularly.

1. Remove needle plate: Use screwdriver to loosen screws, lift plate.
2. Clean feed dogs and bobbin area: Use small brush to remove lint.
3. Oil machine: Apply drop of sewing machine oil to hook race as manual instructs (do not over-oil).
4. Replace needle: Insert new needle with flat side to back, tighten screw.
5. Clean exterior: Use soft, dry cloth.

CAUTION! Never use compressed air; it can force lint into mechanism. Do not use water or solvents.

Safety Information

Always unplug when not in use, during threading, changing needle, or cleaning. Keep hands away from moving parts. Do not operate if cord is damaged. Use proper ventilation. Keep machine dry and away from heat sources.

Warranty & Support

Limited 25-year warranty. For service, contact authorized Brother service center. Register product online at www.brother-usa.com. For support, call 1-877-888-5625 or visit support.brother.com.

Troubleshooting

Reset: Turn off machine, unplug for 60 seconds, then restart.

Service: 1-877-888-5625; www.brother-usa.com