Brother CS6000i Sewing Machine User Manual

The Brother CS6000i is a versatile, feature-rich computerized sewing machine designed for hobbyists and intermediate sewers. It offers 60 built-in stitches, an automatic needle threader, a drop-in top bobbin system, a wide table, and a digital display. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized control panel, Automatic needle threader, Drop-in bobbin system, Wide table, Built-in LED light, Foot pedal, Accessory storage.

Installation & Setup

Unpack and inspect contents. Place on stable, flat surface.

1. Remove all packaging materials and protective covers.
2. Attach the wide table: Align and slide into position until it clicks.
3. Connect foot pedal: Plug into machine port.
4. Connect power: Plug AC adapter into machine and wall outlet.
5. Install needle: Loosen needle clamp screw, insert needle with flat side facing back, tighten screw.

WARNING! Keep hands away from needle area during setup. Ensure machine is unplugged when installing needle.

First-Time Use

Power on machine; follow initial setup steps.

1. Wind bobbin: Place thread on spool pin, guide through bobbin winding tension disc, wind bobbin evenly.
2. Insert bobbin: Drop bobbin into case with thread unwinding counterclockwise; pull thread under tension spring.
3. Thread upper thread: Follow numbered threading path; use automatic needle threader.
4. Draw up bobbin thread: Hold upper thread, turn handwheel toward you to bring bobbin thread up.
5. Select stitch: Use stitch selection dial or buttons.

CAUTION! Always raise needle to highest position before threading or changing presser foot.

Specifications

• Type: Computerized sewing machine.
• Built-in Stitches: 60 stitches.
• Buttonholes: 7 one-step automatic.
• Needle Positions: Adjustable left/right.
• Stitch Length: Adjustable up to 5mm.
• Stitch Width: Adjustable up to 7mm.
• Presser Feet: 6 included snap-on feet.
• Bobbin: Drop-in, Class 15 type.
• Lighting: Built-in LED light.
• Power Source: 120V AC, 60Hz.
• Dimensions: Standard with wide table attached.

Controls and Settings

Access functions via control panel. Front Panel: Power/Stop button, Stitch selection dial, Stitch length/width buttons, Reverse stitch button, Needle up/down button.

Digital Display: Shows stitch number, length, width, and error codes.

Stitch Adjustment: Use +/- buttons for length (0-5mm) and width (0-7mm). Speed Control: Slider adjusts maximum sewing speed. Function Buttons: Reverse, Needle position, Start/Stop (for sewing without foot pedal).

Stitch Selection & Adjustment

Select from 60 stitches: utility, decorative, quilting, heirloom.

1. Turn stitch selection dial to desired stitch number (1-60).
2. View stitch illustration on panel or in manual.
3. Adjust stitch length: Press length button, use +/- to set (shorter for finer fabrics).
4. Adjust stitch width: Press width button, use +/- to set (wider for decorative stitches).
5. For buttonholes: Select buttonhole stitch (31-37), place fabric under foot, press buttonhole lever down.

Tip: Test stitch settings on scrap fabric before sewing project.

Basic Sewing Operations

Supports straight stitch, zigzag, decorative stitches, buttonholes.

1. Prepare fabric: Place under presser foot, lower foot lever.
2. Start sewing: Press foot pedal or Start/Stop button.
3. Guide fabric: Let machine feed; do not pull fabric.
3. Reverse: Press reverse button to reinforce stitches at beginning/end.
4. Finish: Raise needle, raise presser foot, remove fabric, trim threads.
5. Change presser foot: Raise lever, snap off old foot, align new foot, lower lever to lock.
6. Use free arm: Remove wide table for sewing sleeves and cuffs.

WARNING! Keep fingers away from moving needle. Always unplug for needle or foot changes.

Accessories & Attachments

Included accessories: 6 presser feet (zigzag, buttonhole, zipper, overcasting, blind stitch, button sewing), Bobbins (4), Needles (3), Seam ripper/brush, Screwdriver, Spool caps, Spool pin (large and small).

Care & Maintenance

Unplug before cleaning. Clean lint from bobbin area and feed dogs regularly.

1. Remove needle plate: Use screwdriver to loosen screws, lift plate.
2. Clean lint: Use brush to remove lint from bobbin case and surrounding area.
3. Oil: Apply sewing machine oil to hook race as per manual (sparingly).
4. Exterior: Wipe with soft, dry cloth.

CAUTION! Do not use compressed air; it can force lint deeper. Never spray cleaners directly on machine.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Brother Industries, Ltd. For support, visit www.brother-usa.com or contact 1-877-467-4289.

Troubleshooting

Reset: Turn power off, wait 10 seconds, turn on.

Service: 1-877-467-4289; www.brother-usa.com