sewing machine manual brother se600

The Brother SE600 is a computerized sewing and embroidery machine that combines 80 built-in sewing stitches with a 4" x 4" embroidery field. It features a color LCD touch screen, automatic needle threader, drop-in bobbin system, built-in embroidery designs and fonts, USB port for importing designs, and advanced embroidery editing capabilities. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Color LCD touch screen, Automatic needle threader, Drop-in bobbin system, Built-in embroidery designs and fonts, USB port, Free arm, LED work light, Quick-set bobbin, Embroidery hoop (130mm x 180mm).

Unpacking and Setup

Unpack all components carefully. Place machine on stable, flat surface.

1. Remove machine from box: Lift machine by base, not by handwheel or accessories.
2. Install foot controller: Connect to port on right side of machine.
3. Connect power: Plug power cord into machine, then into 120V AC outlet.
4. Attach extension table: Slide onto free arm until it clicks into place.
5. Install embroidery unit: Slide embroidery unit into position until it clicks.

WARNING! Machine is heavy; use proper lifting technique. Ensure power is off during setup.

First-Time Operation

Power on machine; follow on-screen prompts.

1. Wind bobbin: Place thread on spool pin, follow threading guide, press foot controller.
2. Insert bobbin: Place bobbin in case with thread clockwise, pull thread through slot.
3. Thread upper thread: Use automatic needle threader following numbered path.
4. Select stitch: Use touch screen to choose sewing stitch or embroidery design.
5. Test sew: Use scrap fabric to check tension and stitch quality.

CAUTION! Keep fingers away from needle area during operation. Turn power off when threading.

Specifications

• Type: Computerized Sewing and Embroidery Machine
• Sewing Stitches: 80 built-in stitches
• Embroidery Field: 130mm x 180mm (4" x 4")
• Embroidery Designs: 67 built-in designs, 6 embroidery fonts
• Display: Color LCD touch screen
• Maximum Sewing Speed: 710 stitches per minute
• Needle Positions: Adjustable left/right
• Presser Feet: 7 included (zigzag, buttonhole, embroidery, etc.)
• Bobbin: Class 15 (transparent)
• Power Source: 120V AC, 60Hz
• Dimensions: 18.1" x 8.7" x 14.6" (with embroidery unit attached)
• Weight: 17.6 lbs

Controls and Functions

Access functions via touch screen or physical buttons. Front Panel: Power switch, Handwheel, Start/Stop button, Needle up/down button, Speed control slider.

Touch Screen: Stitch selection, Design editing, Lettering, Mirroring, Rotating, Resizing, Thread color selection, Settings menu.

Sewing Settings: Stitch length (0-5mm), Stitch width (0-7mm), Needle position, Thread tension (0-9). Embroidery Settings: Design editing, Hoop selection, Color sequence, Jump stitch trimming. Utility: Language selection (default ENGLISH), Sound on/off, Brightness adjustment, Factory reset.

Threading and Bobbin

Upper Threading: Follow numbered path on machine; use automatic needle threader. Bobbin: Wind evenly; insert with thread pulling clockwise.

1. Turn power off before threading.
2. Raise presser foot and needle to highest position.
3. Place spool on pin, follow threading guide to needle.
4. Use lever for automatic needle threading.
5. For bobbin, ensure thread winds evenly without crossing.

Tip: Use quality thread appropriate for fabric. Clean lint from bobbin area regularly.

Sewing Operations

Supports various fabrics from lightweight to medium weight.

1. Select stitch: Touch screen to choose from utility, decorative, or heirloom stitches.
2. Adjust settings: Modify length, width, tension as needed for fabric.
3. Position fabric: Lower presser foot; guide fabric gently without pulling.
4. Start sewing: Press foot controller or Start/Stop button.
5. Reverse: Press reverse button for backstitching at beginning/end.
6. Buttonholes: Use automatic 1-step buttonhole function with appropriate foot.
7. Zippers: Install zipper foot for invisible or regular zippers.
8. Finish: Raise needle and presser foot; trim threads with built-in cutter.

WARNING! Never sew over pins. Use appropriate needle for fabric type.

Embroidery Operations

Supports built-in designs and imported designs via USB.

1. Attach embroidery unit: Ensure machine is off; slide unit until click.
2. Select design: Choose from built-in library or import via USB.
3. Edit design: Use touch screen to resize, rotate, mirror, or combine designs.
4. Hoop fabric: Use stabilizer; tighten fabric in hoop without stretching.
5. Attach hoop: Place on embroidery unit; lower presser foot lever.
6. Thread colors: Machine will prompt for color changes during embroidery.
7. Start embroidery: Press Start/Stop button; machine trims jump stitches automatically.
8. Monitor progress: Watch on screen; pause if needed for thread changes or issues.

CAUTION! Always use stabilizer appropriate for fabric. Do not move hoop during embroidery.

Care & Maintenance

Unplug before cleaning. Clean lint regularly; oil as specified in manual.

1. Daily: Remove lint from bobbin area and feed dogs with brush provided.
2. Weekly: Clean race hook area; apply small drop of sewing machine oil if needed.
3. Monthly: Check needle for damage; replace if bent or dull.
4. Storage: Cover machine when not in use; store in dry area.

CAUTION! Use only sewing machine oil. Never spray cleaners directly on machine.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Brother Industries, Ltd. For support, visit www.brother-usa.com or contact 1-877-467-4289. Machine complies with UL standards for safety. Embroidery designs may be subject to copyright restrictions.

Troubleshooting

Reset: Turn machine off, wait 10 seconds, turn back on. For persistent issues, perform factory reset via settings menu.

Service: 1-877-467-4289; www.brother-usa.com